collection-banner-image collection-banner-image

Professional Zinc Alloy Surface Finishing Solutions

Die-Casting - Intermediate

Die-Casting Porosity: Why It Becomes a Plating Blister Two Weeks Later
2026-10-09 16:02:01

Die-Casting Porosity: Why It Becomes a Plating Blister Two Weeks Later

A mid-sized manufacturer specializing in zinc-alloy die-casting recently encountered a perplexing issue: parts that passed...
Read MoreDie-Casting Porosity: Why It Becomes a Plating Blister Two Weeks Later
Process Parameter Sheet Template for Zinc Alloy Die Casting: Shot Speed, Switch Point and Hold Pressure
2026-09-23 00:00:00

Process Parameter Sheet Template for Zinc Alloy Die Casting: Shot Speed, Switch Point and Hold Pressure

Read MoreProcess Parameter Sheet Template for Zinc Alloy Die Casting: Shot Speed, Switch Point and Hold Pressure
Shot-End Tuning on Zinc Die-Casting: Plunger Tip, Sleeve Wear and the Signature of a Healthy Shot
2026-09-03 19:36:41

Shot-End Tuning on Zinc Die-Casting: Plunger Tip, Sleeve Wear and the Signature of a Healthy Shot

Read MoreShot-End Tuning on Zinc Die-Casting: Plunger Tip, Sleeve Wear and the Signature of a Healthy Shot
Sliders Sticking Every Afternoon: Die Thermal Balance and Temperature Cycling in Zinc Die Casting
2026-08-31 00:00:00

Sliders Sticking Every Afternoon: Die Thermal Balance and Temperature Cycling in Zinc Die Casting

Read MoreSliders Sticking Every Afternoon: Die Thermal Balance and Temperature Cycling in Zinc Die Casting
Cold Shuts and Flow Marks on Zinc Die-Castings: Mould Temperature, Gate Wear and Venting
2026-08-25 13:14:27

Cold Shuts and Flow Marks on Zinc Die-Castings: Mould Temperature, Gate Wear and Venting

Read MoreCold Shuts and Flow Marks on Zinc Die-Castings: Mould Temperature, Gate Wear and Venting
Gas vs Shrinkage Porosity in Zinc Die-Casting: Section the Part, Tune the Shot and Make the Fix Stick
2026-08-25 13:14:27

Gas vs Shrinkage Porosity in Zinc Die-Casting: Section the Part, Tune the Shot and Make the Fix Stick

Read MoreGas vs Shrinkage Porosity in Zinc Die-Casting: Section the Part, Tune the Shot and Make the Fix Stick
Die-Casting Problem Areas for Intermediate Technicians: Porosity, Flash and Shot Tuning
2026-08-25 09:44:31

Die-Casting Problem Areas for Intermediate Technicians: Porosity, Flash and Shot Tuning

Read MoreDie-Casting Problem Areas for Intermediate Technicians: Porosity, Flash and Shot Tuning
Die-Casting Machine Settings for Zinc Hardware: Shot, Mould Temperature and Cycle Windows That Prevent Cold Shuts and Flash
2026-08-24 18:51:09

Die-Casting Machine Settings for Zinc Hardware: Shot, Mould Temperature and Cycle Windows That Prevent Cold Shuts and Flash

Read MoreDie-Casting Machine Settings for Zinc Hardware: Shot, Mould Temperature and Cycle Windows That Prevent Cold Shuts and Flash
Zinc Die-Casting Defects That Reach the Finishing Line: Porosity, Cold Shuts and Flash — What Platers and Painters Can and Cannot Fix
2026-08-24 11:18:55

Zinc Die-Casting Defects That Reach the Finishing Line: Porosity, Cold Shuts and Flash — What Platers and Painters Can and Cannot Fix

Read MoreZinc Die-Casting Defects That Reach the Finishing Line: Porosity, Cold Shuts and Flash — What Platers and Painters Can and Cannot Fix