Polissage à sec du baril

🌰 Part I: Dry Media Selection (The Carriers)

The choice of media depends on the density of the wood and the shape of your product.

1 Walnut Shell Grit (The Cutter)

Material: Crushed Walnut Shells.

Hardness: Hard and dense.

Function: Cutting & Leveling. It removes the die-cast skin and minor scratches.

Grit Selection:

Coarse (8-12 Mesh): For heavy deburring.

Medium (16-20 Mesh): Standard for zipper pulls.

Fine (30 Mesh): For detailed logos to avoid lodging.

2 Corn Cob Grit (The Polisher)

Material: Crushed Corn Cobs.

Hardness: Soft and absorbent.

Function: Final Mirror Finish. It holds the fine polishing paste and wipes the metal clean.

Grit Selection:

[QLQ] Premium Cob (16-20 Mesh): The standard for high gloss.

Dust-Free Grade: Essential to prevent dust from packing into the zipper holes.

3 Bamboo Cubes / Wooden Pegs

Material: Hardwood or Bamboo diamonds.

Function: Used for heavy parts to prevent impingement (denting). They act as spacers.

🧴 Part II: The Chemical Agents (The Pastes)

Dry media alone does nothing. You must "charge" the media with [QLQ] Polishing Compounds.

1 [QLQ] Dry Cutting Cream (White/Grey)

Base: Aluminum Oxide + Stearic Acid.

Application: Mixed with Walnut Shell.

Goal: Removes the "Orange Peel" from the Zinc casting.

2 [QLQ] Mirror Paste (Blue/Green)

Base: Chromium Oxide + High-Temp Grease.

Application: Mixed with Corn Cob.

Goal: Creates the "Black Mirror" deep reflection.

3 [QLQ] Media Rejuvenator Oil

Application: Added when the media gets too dry or dusty. It restores the "stickiness" of the paste to the shell.

⚙️ Part III: Equipment & Process Workflow

Machine Type: Centrifugal Barrel Finisher (High Speed)

Do not use a standard rotary tumbler (Octagonal drum) for Zinc unless you have 24 hours to wait. Use a Centrifugal Machine (Planetary Motion).

G-Force: Generates 10G - 15G force.

Speed: Polishes in 1-2 hours instead of 20 hours.

Step 1: The Dry Grind (Leveling)

Media: Walnut Shell (Medium).

Compound: [QLQ] Dry Cutting Cream.

Ratio: 1 Part Zinc : 4 Parts Media.

Time: 60 – 90 Minutes.

Temperature: The barrel will get hot (50°C-60°C). This is normal. The heat helps the paste flow.

Step 2: The Dry Polish (Mirror)

Media: Corn Cob Grit.

Compound: [QLQ] Mirror Paste.

Ratio: 1 Part Zinc : 5 Parts Media. (Higher media ratio protects the shine).

Time: 30 – 45 Minutes.

Result: Parts come out looking like Chrome Plated, even before plating.

👨‍🍳 Part IV: The Master's "Recipe" (Ratios & Operations)

1 New Media Break-In (The "Pre-Charge")

The Mistake: Pouring fresh walnut shell and parts into the machine immediately.

The Consequence: The dry shell scratches the zinc.

The Master's Fix:

Run the new media Empty (no parts) with [QLQ] Compound for 2 hours.

Dosage: 3% - 5% of Media Weight.

This coats every grain of walnut with a layer of grease/abrasive. The media should feel "Damp" but not sticky.

2 Daily Re-Charging

Frequency: Every 2-3 Batches.

Dosage: Add small amount of [QLQ] Compound (approx 0.5% of weight).

Visual Check: Grab a handful of corn cob. Squeeze it.

Good: It clumps slightly then falls apart.

Too Dry: It creates dust. (Add Compound or Oil).

Too Wet: It sticks to your hand like mud. (Run with no parts or add fresh media).

3 Temperature Control

Ideal Temp: 40°C – 60°C.

Cold: The paste is hard and scratches.

Hot (>70°C): The Zinc alloy might darken, and the corn cob might burn/char.

Tip: If the machine is cold in the morning, run it empty for 15 mins to warm up the friction.

🛑 Part V: Troubleshooting & Maintenance

Defect: "Orange Peel" Texture

Cause: The Cutting Step (Walnut) was too short. You polished the bumps instead of flattening them.

Fix: Increase Step 1 time. Ensure Walnut Shell is not worn out (round and smooth).

Defect: Media Lodging

Cause: Media size matches the zipper pull hole.

Fix: Switch to a mix of sizes (e.g., 70% Medium + 30% Fine) or change Mesh size completely. Use [QLQ] Anti-Lodging Separator screens.

Defect: Dull Film / Haze

Cause: Media is "Dead" (Saturated with metal dust and old grease).

Fix:

Quick Fix: Run the media with [QLQ] Corn Cob (plain) to absorb the dirt.

Real Fix: Replace the media. Walnut lasts ~200 hours. Corn Cob lasts ~100 hours.

Defect: Parts turning Black

Cause: Overheating or too much compound.

Fix: Check ventilation of the machine. Add fresh, clean corn cob to dilute the mix.

💡 Part VI: Master's Efficiency Secrets

1 The "Dedicated Barrel" Rule

Never mix the barrels.

Mark Barrel A: "Cutting Only" (Walnut).

Mark Barrel B: "Polishing Only" (Corn Cob).

If you put Corn Cob in a dirty Walnut barrel, the Corn Cob gets contaminated instantly and will scratch your mirror finish.

2 The "Dust Extraction" System

Dry polishing creates dust.

Install a vacuum extraction line on the sorting machine.

Why? Dust on the part = Pitting in the plating tank. The parts must be 100% dust-free before entering the plating line.

3 The "Warm Transfer"

Do not let parts cool down between Step 1 and Step 2.

Transfer the hot parts directly from Walnut to Corn Cob.

The residual heat helps the polishing paste work immediately.

🛒 Costing & Consumables Checklist

Final Word from the Master

"Wet polishing is for speed. Dry polishing is for luxury. If your client is Louis Vuitton or Gucci, you must use Dry Polishing. The depth of the shine is unmatched."